Главная > Документ
|Информация о документе|
|Доступные форматы для скачивания:|
This information only applies to products manufactured in the following location(s): Europe
TECTYL 122-A is a solvent cutback wax/asphaltic base, thixotropic corrosion preventive compound.
TECTYL 122-A is suitable to be applied to the undersides of vehicles.
TECTYL 122-Adries to a relatively firm, black, resilient, tough film.
Flashpoint; PMCC 40 °C
Specific Gravity @ 60°F 0.91 kg/ltr
Recommended Dry Film Thickness 250 microns minimum
Theoretical Coverage @ Avg. Recommended DFT 2.1 m²/l
Non Volatile 60 weight %
Viscosity; Brookfield @ 25°C
(at time of manufacture)
@ 2 RPM: 25.000 mPa.s (cP)
@ 20 RPM: 7.000 mPa.s (cP)
Dry to Touch Time @ 25°C ± 4 hours
Dry Time @ 25°C ±24 hours
Volatile Organic Content (VOC) (ASTM D-3960) 362 g/l
Accelerated Corrosion Tests:
@ Avg. Recommended DFT
Salt Spray; 5 % NaCl @ 35°C; DIN 50 021 (ASTM B-117) 40 days
(DIN 1623 Steel Panels)
Humidity; 100 % RH; @ 40°C; DIN 50 017-KK 100 days
относится только к продукции,
произведенной в следующие места
The maximum performance of TECTYL 122-A can be achieved only when the metal surfaces to be
protected are clean, dry and free of rust, oil and mill scale. Valvoline recommends that the metal
substrate temperature be 10-35 °C at the time of product application.
Avoid direct contact of the product with PVC due to possible material incompatibility.
TECTYL 122-A is formulated to be used as supplied. Ensure uniform consistency prior to use.
Continued stirring is generally not required. If the product thickens due to cold storage or loss of solvent
during use, contact Valvoline. DO NOT THIN TECTYL 122-A. Incorrect thinning will affect film build, dry
time and product performance. Valvoline recommends that the ambient and product temperature be 10-
35 °C at the time of product application. TECTYL 122-A can be applied by airless spray or brush.
TECTYL 122-A can be removed with mineral spirits or any similar petroleum solvent, hot alkaline wash
or low pressure steam.
TECTYL 122-A should be stored at temperatures between 10-35 °C. Mild agitation is recommended prior
to use. Due to its composition TECTYL 122-A can be subject to postproduction viscosity changes during
Under proper storage conditions TECTYL 122-A can have a shelf life of 3 years minimum.
Adequate ventilation is required for cure and to ensure against formation of combustible liquid. THE
PARTIALLY CURED FILM SHOULD NOT BE EXPOSED TO IGNITION SOURCES SUCH AS FLARES,
FLAMES, SPARKS, EXCESSIVE HEAT OR TORCHES. Refer to Valvoline’s Material Safety Data Sheet
for additional handling and first aid information.
The addition of any product over or under this coating is not recommended. The use of additional
coatings could result in chemical incompatibility, thus affecting the performance of this coating as stated
in the Typical Properties section. If a primer, other than a Valvoline recommended product is required,
written authorization must be obtained from Valvoline.
- ... only applies to products ... to information belonging to ... to the size of the settlement. Followed approach of other jurisdictions, concluding that fees in the ... manufacturers Court-ordered distribution: good in this case, especially because of the flaws in ...
The “Environment for Europe” mid-term review of the Astana Conference main outcomes: main findings of the reviewДокумент... in the country and around the world, their results, following of the information about the works related to ... that apply to a product or technical procedures for production processes—are being amended in ...
Основной курс (Essential Course). Упражнения по интонации (Exercises in Intonation). Упражнения по грамматике (Grammar Exercises)Учебник... the "Black country". In Birmingham, the centre of this area, and in the manufacturing ... products, etc. The largest coal and iron fields in Britain are located in the ... In this case the head is called Sliding. Compare: 1. Listen carefully to the following ...
Методические указания по дисциплине «Английский язык» Тексты для самостоятельной работы для студентов 1, 2 курсов для направленияМетодические указания... factor in the location of cities. The earliest settlers realized this need ... the heaviest trafficked roads. Until now these products have had to be manufactured in ... service population group employed in the following; Municipal administrative and public ...
- ... the brain important information about the location or position of the ... in correct position. This is necessary not only to restore the bone structures, but to place the ... and the production of new chemical substances requiring water in the manufacturing ...